"Furniture Refinishing Tips"
Refinishing furniture suggestions disdain,
secret work, techniques and trade secrets
Furniture from the doctor
Sample Newsletter
Furniture doctor newsletter
August/4/2001
In this case I will talk about filling defect, and various
The technique is available.
# 1 - fill Wax sticks - Good for scratches, dings and small, or the name of dents.
For only scratches in the early shift with the stick until it is full.
Wipe down off the excess with a cloth.
To dings, dents or name, you can also try to nudge the entire disability.
Or you may be to melt into the defect with some equipment burning, simply melt
to fill only on the surface, then the goods off the excess with cabinet
scraper or sandpaper.
Note if the work is completed with the cut, protect the surface with balsam,
or paint thinner.
-------------------------------------------------- --------------------
# 2 - shellac stick - Or Burn-in stick - this must be disbursed to
disabilities. The surface must be protected with ointment as well, plus
the excess must be removed by burning the equipment.
This technique is mastered a little more difficult.
__________________________________________________________________
# 3 - Wood putty - This technique is easier to use, but difficult to complete.
You can use properly, applied to disability, under the sand, then stain
the match.
Or putty color that the first effect.
You can use regular stain, or aniline dye to add color.
__________________________________________________________________
# 4 - Saw dust and white glue.
Sand in the area not only to gather dust see the advantages, and
intervene in some glue, and use this as filler.
Note; - duration has been using this technique for years.
______________________________________________________________
# 5 - Boil the disabled with steam.
This technique will display several times with disabilities all the way back,
but not always!
How does it do?
Some people place a wet cloth on the run, and iron handicap
more than that. Check it often for the results.
Some times you can only descend to the water and place disabled
end of the soldering gun to the disabled, always make sure
for water has been present in the area of the wound, to increase disability
to the surface. Do not let it dry out .!!!!!
___________________________________________________________________
# 6 - Hot Glue Gun.
YES! You read it right!
I found this technique by curiosity.
I only want to try to see whether it would work.
Last week I work in the cabinet above, who have lost the corner
I should be back building about 1 / 8 inches deep by three inches long timber lost.
Corners can be difficult to rebuild using other methods.
I glued a straight edge on both sides, and so the oil is applied hot glue
will not stick.
Next I remember is applied to the disabled and allow cool.
Then I remove the straight edge, and apply masking tape to the surrounding
completed to protect the finish area.
Then I started again hot glue, use a sharp knife, to remove
most of the excess.
Then I switch to some # 80 grit sand paper and remove the masking tape
sand and a hot glue together with the rest of the print edge
on the cabinet edge image to see some dust from the hot glue into the wound
area.
This is automatically added color or dragged to the hot corner areas, and mixed
hot corners of the damaged area with both.
__________________________________________________________________________
# 7 - Sometimes you can cut the damaged areas, and replace them with new
from the same type of wood. Especially from the corner of the locker or TOPS.
Then you can go back and stain it to match.
This technique takes longer to take control.
____________________________________________________________________________
# 8 - Surface - Some times you can use a plug cutter, to drill out small
disability, and insert a plug, then plan and stain to match.
Using this technique you will choose to close the timber as possible to match
color and grain from the area of the wound.
Plus you will be using the wood surface to drill your new replacement plug.
_______________________________________________________________________________
Want more tips?
Customers paid for my Online Clinic 3 years, I received a newsletter with more than 50 issues.
Plus my Q & A page with answers to more than 200 questions. click here for a sample
Plus ... Access to more than 127Guides on Repairing & Refinishing Furniture. click here for the contents
Unlimited Plus FREE email consultation ...
All Together, you will find thousands of tips, tricks of the trade, trade secrets, techniques, and solutions to guide you ..... Illustration by many ....
Advantage I take from the experience of many years ...
Learn Furniture Refinishing, and the improvements and find all my trade secrets, techniques, and secret laboratories. more info. more info
Furniture Refinishing receive tips in your e mail.
FREE Newsletter Here I subscribe.
